Synthesis of nonionic-anionic colloidal systems based on alkaline and ammonium β-nonylphenol polyethyleneoxy (n = 3-20) propionates/dodecylbenzenesulfonates with prospects for food hygiene

Background The main objective of this work was to obtain a binary system of surface-active components (nonionic soap – alkaline and/or ammonium dodecylbenzenesulfonate) with potential competences in food hygiene, by accessing a scheme of classical reactions (cyanoethylation, total acid hydrolysis and stoichiometric neutralization with inorganic alkaline and/or organic ammonium bases) adapted to heterogeneously polyethoxylated nonylphenols (n = 3-20). In the processing system mentioned, dodecylbenzenesulfonic acid, initially the acid catalyst for the exhaustive hydrolysis of β-nonylphenolpolyethyleneoxy (n = 3-20) propionitriles, becomes together with the nonionic soap formed the second surface-active component of the binary system. Results In the reaction scheme adopted the influence of the main operating (duration, temperature, molar ratio of reagents) and structural parameters (degree of oligomerization of the polyoxyethylene chain) on the processing yields for the synthetic steps was followed. The favorable role of the polyoxyethylene chain size is remarked, through its specific conformation and its alkaline cations sequestration competences on the yields of cyanoethylation, but also the beneficial influence of phase-transfer catalysts in the total acid hydrolysis step. The chemical stability of dodecylbenzenesulfonic acid (DBSH) at the temperature and strongly acidic pH of the reaction environment is confirmed. The controlled change of the amount of DBSH in the final binary system will later confer it potential colloidal competences in food hygiene receipts. Conclusions The preliminary synthetic tests performed confirmed the prospect of obtaining a broad range of useful colloidal competences in various food hygiene scenarios.


Background
Good household hygiene [1][2][3][4][5][6] is important throughout the world for preventing infectious diseases. For additional protection, manufacturers are developing antibacterial products specifically for industrial and home use. These products are not true disinfectants; but they do decrease the number of living microorganisms on skin or surfaces to significantly lower levels.
Among the new generation of antibacterial household products that have recently appeared on the market, hand dishwashing liquids have become increasingly popular. They are classical dishwashing liquids based on anionic and nonionic surfactants, to which one or more antibacterial agents have been added. These formulae have been optimized to maintain their cleaning/ degreasing performance and to fight bacteria on hands, in the washing solution, and on washing implements. In the United States, these products are regulated by either the EPA (Environmental Protection Agency) or the FDA (Food and Drug Administration), depending on specific claims.
Sanitation within the food industry means the adequate treatment of food-contact surfaces by a process that is effective in destroying vegetative cells of microorganisms of public health significance, and in substantially reducing the numbers of other undesirable microorganisms, but without adversely affecting the food or its safety for the consumer (FDA, Code of Federal Regulations (CFR), 21CFR110, USA). Sanitation Standard Operating Procedures are mandatory for food industries in US, which are regulated by 9 CFR part 416 in conjunction with 21 CFR part 178.1010. Similarly, in Japan and Europe, food hygiene has to be achieved through compliance with food sanitation laws.
Traditional soaps ( Figure 1A) (alkaline salts of longchain acids) have been known as structures and practical importance (sanitation agents) for hundreds of years since the discovery of the alkaline hydrolysis process (saponification of fats and oils). The two major drawbacks of classical soaps are their low solubility in aqueous solutions (opalescence) and their high sensitivity to the hardness of waters used in sanitation processes due to the low solubility of their calcium and magnesium salts.
Normally, the degree of the ethoxylation (oligomerization degree of ethylene oxide in the polyoxyethylene chain) (n) is between 2 and 20(50) units ethylene oxide. The sodium salts of polyether carboxylic acids are water soluble, mild, and very resistant against water hardness and have extremely good dispersal and emulsifying power.

) instead of carboxymethylation only
1939 is widely accepted in the specialty literature [15] as the year of the first report of nonionic soaps, through the patent granted to H. Haussmann at I.G. Farben Industrie. It was a natural consequence, on the one hand, of the scarcity of fatty materials which began to manifest ever more acutely in Europe at the beginning of World War II, but also of the poor quality of waters used in the technological processes (excessive hardness), which made traditional soaps hardly practical.
The period that followed this reference date can be characterized by: ▪ steadily increasing interest in the knowledge of colloidal competencies and structural diversification of the range of nonionic soaps; ▪ major interest for the aliphatic series against the aromatic; ▪ dissemination of research results preferentially in the patent literature of Europe (Germany) and U.S.A.
Currently the following procedures for obtaining nonionic soaps are frequently recorded ( Figure 2): 1. Oxidation of linear polyethoxylated (n = 3-20) higher alcohols (C 12 H 25 -C 18 H 37 ) and of polyethoxylated nonylphenols (n = 3-20): with chromic and nitric acid [16]; in the presence of titanium dioxide in basic medium (additional conditions not specified) [17], and catalytic oxidation with platinum, palladium and/ or other metals-based catalysts, respectively [18], when together with the corresponding nonionic soaps, the presence of free higher alcohols due to the scission of etheric "bridges" is confirmed ( Figure 2A)  monochloroacetic/ monochloropropionic acid at molar ratios in the range of 1/0,7-1/1,25, at 20-140°C at atmospheric pressure [18]. According to the literature data [19], the strongest effect on the ionization of the carboxyl group is exerted by the chlorine atom in the α position to the group. The influence decreases with distance, being weaker in the β position than in α and even weaker in the γ position, and therefore η 1 > η 2 > η 3 ( Figure 2B). According to the electronic theory, the increased acidity of halogenated acids, when compared with the corresponding non-halogenated acids, is due to the electron-attracting inductive effect of the halogen atoms (−I effect), the more stronger as it is located closer in the chain to the carboxyl group. 3. Reaction of polyethoxylated (n = 2-50 ethylene oxide units) nonylphenols with an alkaline hydroxide at 100-120°C with the intermediate formation of the corresponding phenoxide, which subsequently with γ-butyrolactone at 100-110°C forms with yields exceeding 85% a range of nonionic surface-active carboxybutyric compounds [20] ( Figure 2D). Similarly, using β-propiolactone ( Figure 2C) nonionic carboxypropionic soaps can be synthesized.
Alkaline and/or ammonium alkylarylsulfonates (ndodecylbenzenesulfonates) ( Figure 3A), anionic surface-active compounds, are traditional components of the active substance in many washing/food sanitizing receipts. Sulfonation of aromatic rings (in benzene and/or naphthalene) is widely used in the technological practice in the processing of wetting agents, emulsifiers, demulsifiers ( Figure 3A and 3B). It is a reversible process of unimolecular electrophilic substitution (SE1), in which the actual sulfonation agent is SO 3 ( Figure 3C). Dodecylbenzenesulfonic acid (DBSH) in technical products from the technological practice is present in proportion of over 98% together with ca. 2% residual sulfuric acid. In this study both components were acid catalysts in the exhaustive hydrolysis of β-nonylphenoxy (NF) polyethyleneoxy (n = 3-20) propionitriles [NF(EO) n -PN)] to βnonylphenoxy (NF) polyethyleneoxy (n = 3-20) propionic acids [NF(EO) n -PC)] ( Figure 4).
In this paper a sequence of classical reactions is adopted for the first time as the operating strategy, constructively adapted to obtain a new product range of nonionic soaps based on alkaline and/or ethanolammonium β-nonylphenolpolyethyleneoxy (n = 3-20) propionates. In this scheme, cyanoethylation of the hydroxyl functional group substitutes the oxidation reaction and/or the reaction with sodium monochloroacetate with the following major benefits: eliminates the byproducts difficult to monitor as diversity and share of the oxidation products (radical reactions); eliminates the increased corrosion of industrial installations due to hydrochloric acid (reaction with sodium monochloroacetate). In the proposed draft version the accidental formation of oligomers of the acrylic monomer under alkaline catalysis is inhibited, through the action of FeSO 4 (Fe 2+ ) associated with the other working parameters, and practically quantitative yields of nucleophilic addition are ensured. This work reports for the first time the importance of certain impurities (water, polyethyleneglycols, free nonylphenol) in the technical products and studies after prior selective purification their qualitative and quantitative influence on the processing yields by controlled subsequent additivation.
In the conducted study for the first time is reported and argued the different development of the cyanoethylation of free nonylphenol compared to that of polyethoxylated nonylphenols (n = 3-20), highlighting the favorable role of polyoxyethylene chains grafted at oligomerization degrees n ≥ 3. In the same context is emphasized the decisive role of phase-transfer catalysts in the first case.
In the conducted study is accepted as operating premise and confirmed for the first time the favorable effect of dodecylbenzenesulphonic acid in the exhaustive acid catalysis of β-substituted propionates, but also in the final structuring of a flexible binary nonionic-ionic colloidal system with real possibilities of implementation in food sanitation systems.

Results and discussions
A continuation of the colloidal optimization preoccupations and diversification of nonionic soaps as such and/ or in combination [26,30], this work is aiming at the controlled simultaneous obtaining of surface-active mixtures based on alkaline and ammonium β-nonylphenoxy (NF) polyethyleneoxy (n = [3][4][5][6][7][8][9][10][11][12][13][14][15][16][17][18][19][20] propionates/dodecylbenzenesulfonates by following the diagram of operations in Figure 4. Knowing the factors that influence the evolution of the processes shown in the block diagram of operations ( Figure 4) is of great importance in the analysis of basic mechanisms of reactions in the "boundary layer", for the intensification of mass and/or energy transfer coefficients by increasing the contact surfaces in heterogeneous processes (hydrolysis), and reducing the thickness of interphase separation interfaces etc., respectively.
Knowing the main stage parameters that may affect the processing yields and/or composition of the final reaction mixture, the mutual dependence was followed through the gradual, successive change of one of them and keeping the other constant in order to maximize the share of the main reaction product, β-substituted propionitriles and/or β-nonylphenolpolyethyleneoxy (n = 3-20) propionic acids, and to minimize the byproducts (mainly oligomers and/or polymers of the acrylonitrile monomer), respectively.
The resulting experimental database enabled the mathematical processing and the determination of the nature of the dependence equations (linear, logarithmic, exponential or polynomial) with the maximum correlation coefficient.
In the process of cyanoethylation of polyethoxylated nonylphenols, the reaction time favors the formation of βsubstituted propionitriles [R(EO)nPN] up to 180 minutes, and the oligomerization of the acrylic monomer throughout the process ( Figure 5,6). After this period, the cyanoethylation yields decrease due to their prolonged contact with the basic medium, suggesting the reversible character at prolonged contact between the reactants (Figure 7). Its maximum value is achieved at lower reaction times as the oligomerization degree (n) of the polyoxyethylene chain increases, which may suggest the involvement of the polyoxyethylene chain in the process ( Figure 6).
Increasing the amount of catalyst above the optimal value (4-5·10 -3 mol/L) increases the alkalinity of the environment and favors the oligomerization reactions of the acrylic monomer. In the concentration range of 15-50·10 -3 mol/L the content of [R(EO) n PN] decreases, in parallel with the rapid growth of the oligomers content. In the series of polyoxyethylene chain homologues, the maximum cyanoethylation yield is reached at limited values of catalyst concentration. At the same concentration of catalyst the dimensional increase of the polyoxyethylene chain determines a sensible increase of the nucleophilic addition yields, but also a reduction in the amount of oligomers formed, probably due to the solvation of the acrylic monomer in the polyether chain (Figures 8,9,10).
The initial presence of free nonylphenol in varying amounts (5-40%) negatively influences the cyanoethylation yields through the equivalent monomer consumption and the lower cyanoethylation rate [the nucleophilicity of  the alkaline nonylphenoxide decreases due to the (−Is) and (+Es) effects, respectively, of opposite sign]. The phenomenon can be explained on the one hand through the "steric hindrance" effect due to the hydrocarbon chain, and through the lower nucleophilic activity of the alkaline nonylphenoxide, compared to that of the polyethoxylated nonylphenols ( Figure 11). The presence of polyethyleneglycols in varying amounts (1-15%) in the processing mixture ( Figure 12) of polyethoxylated nonylphenols, influences the cyanoethylation yields in two opposite directions: ▪ high consumption of monomer (1-2 moles/mol PEG) with formation of polyethyleneglycol (n = 3-30) dipropionitriles (dicyanoethylated polyethyleneglycols); ▪ participation of dicyanoethylated polyethyleneglycols in the cyanoethylation process, as mono-or diprotected oligoglymes (PTC) (activation of the alkaline nonylphenoxides through the coordination of the alkaline cation). The favorable contribution to the cyanoethylation yields depends on the average degree of polyethoxylation of nonylphenol (n), since the distribution of polyoxyethylene chain homologues is larger, as the nonylphenol is more highly polyethoxylated, and the distribution of PEG homologues in the (n = 3-30) range is wider than that of the homologues in NF-(EO) n -H (n = 3-20), for the same average ethylene oxide content.
In the processing conditions mentioned were found increased amounts of: ▪ oligomers in the final reaction mixture, because alkaline polyethyleneglycolates, as bidentate nucleophilic agents, have higher alkalinity than alkaline nonylphenoxides ( Figure 12); ▪ β-nonylphenoxy propionitriles, proportional to the amount of polyethyleneglycols, due to the favorable effect of phase-transfer catalysis ( Figure 12) In the conducted study the formation of oligomers of acrylonitrile in basic medium was avoided through the introduction of anhydrous ferrous sulfate (FeSO 4 ) ( Figure 13) as inhibitor of the oligomerization/ polymerization, respectively, of the acrylic monomer. For the addition of 1% inhibitor, the yield of the cyanoethylation of free nonylphenol increases by more than 10%, without the formation of oligomers. Similar results are also obtained in the homologous series of polyethoxylated nonylphenols NF(EO) n H (n = 3-20).
The polyoxyethylene chain, with its specific conformation [31], intervenes in the cyanoethylation process in nonpolar reaction media through the activation of the nucleophile, so that the processing yields for polyethoxylated nonylphenols, with the same polyoxyethylene chain in the homologous series (n = 3-20), increase.
As confirmed experimentally the hypothesis of active participation of the polyoxyethylene chain in the cyanoethylation process allowed the approximation of the coordination numbers of the alkali cations with the phase-transfer catalyst (GLYME-n-PN) in the class of "homogeneous" dicyanoethylated polyethyleneglycols (n = 3, 6,9,12,16,20). (The notion of phase transfer is referring to the movement through the interface of the alkaline cation sequestered in the "reverse" micelle/ medium system).
From the analysis of experimental data it can be stated that the cyanoethylation of free (NFOH) and/or polyethoxylated [NF(EO) n H] nonylphenol proceeds by a complex mechanism, in which the rate-determining step is the actual nucleophilic addition. Its precursive and subsequent steps are protolytic equilibria (acid-base), in which the nucleophilic agent characteristic to the hydroxyl substrate is formed, or the carbanionic structure resulting from the addition is stabilized, respectively.
Since in the formation of the activated complex are involved a polarized (the acrylic monomer) and an ionic (alkaline nonylphenoxide) molecular species, the reaction is strongly influenced by solvation effects (coordination), due to both the polarity of the medium and the nature of the alkaline cation. The increase of the ionic character of the nucleophile-alkaline cation bond favors the coordination effects specific to the conformation of polyoxyethylene chains (n = 3-30), therefore comparable with similar diprotected chains (dicyanoethylated polyethyleneglycols). Simultaneously with the reaction rate increases the monomer consumption. Determination of the partial reaction orders with respect to glymes allowed the indirect estimation of the size of the "elementary cell" of coordination of the alkaline cation to the value of 8-9.
Determination of the partial reaction orders with respect to glymes allowed the indirect estimation of the size of the "elementary cell" of coordination of the alkaline cation to the value of 8-9 [26,[32][33][34]. The statements expressed and mechanisms of action formulated represent our own interpretations of the experimental data recorded. They are supported by the results, comments, discussions and literature on the currently widely  accepted geometry and spatial conformation of the acyclic polyoxyethylene chains with various degrees of oligomerization (n) [35][36][37][38][39].
A reversible reaction, cyanoethylation is determined by temperature, duration, excess reactant (monomer) and the addition products. Secondary products existent in the raw materials (free nonylphenols, polyethyleneglycols, traces of water) and the oligomers of acrylonitrile in the reaction product, negatively affect the yields of the nucleophilic addition through the monomer consumption and the subsequent purification difficulties. That is why the presence of oligomerization inhibitors (FeSO 4 ) is necessary and recommended.
The heterogeneous nature of the acid hydrolysis systems affects the contact between the reactants (βnonylphenoxy-polyethyleneoxy-propionitriles, water and catalyst), therefore the prior indicative evaluation of the HLB balance (hydrophilic/hydrophobic balance) was imposed, and that of the water solubility of β-substituted propionitriles and propionic acids as reaction products, respectively (Table 1).
From the analysis of data presented in Table 1 the following aspects can be observed: ▪ the HLB balance increases with the hydrophilicity (the polyethoxylation degree of nonylphenol) of the β-substituted propionitriles; ▪ their solubility evaluated by the value of the %EO/N ratio [40,41] and verified practically by determining the water number (Karabinos method) is high.
In order to assess these influences, initially the acid hydrolysis was studied on β-nonylphenoxy (NF) (n = 0) propionitrile (NF-O-PN), immiscible with water. In this respect, the temperature dependence of the composition of the processing mixture was followed within the range 80-160°C (Figure 14), initially without the influence (presence) of the phase-transfer catalyst. From the comparative analysis of the experimental data it is noted that the yield of nonylphenoxypropionic acid (NF-O-PC) increases throughout the specified temperature range. The content of nonylphenoxypropionitrile (NF-O-PN) decreases practically, while the amount of free nonylphenol increases predominantly in the range 120-160°C due to the splitting in strong acidic medium of the "ether bridge" formed in the cyanoethylation step.
Under the specified conditions the evolutions of the proportions of NF-O-PN and NF-O-PC, respectively, for a molar ratio DBSH/NF-O-PN 1/1, without PTC suggests a downward trend for the propionitrile and an upward one for the content of propionic acid. Simultaneously with the increase of temperature in the range 80-160°C this trend is maintained, but the increase of the free nonylphenol content is also noted. This confirms the reversible character of the hydrolysis process due to the scission in strongly acidic medium at temperatures above 120°C of the "ether bridge" in NF-O-PN.
The dependence of the composition of the processing mixture and of conversion yields, respectively, on the operating parameters and/or structural factors for the heterogeneous homologous series of polyethoxylated nonylphenols NF(EO) n -H (n = 3, 6,9,12,16,20) was performed initially on technical products purified of Figure 13 Dependence of the cyanoethylation yield of free nonylphenol, on the content of polymerization inhibitor (anhydrous FeSO 4 ), molar ratio acrylonitrile/free nonylphenol 1.1/1, temperature 30°C, processing time 2 h, solvent toluene, catalyst concentration 5x10 -3 mol/L. Table 1 Reference physico-chemical parameters for the colloidal behavior of β-nonylphenoxy (NF) polyethyleneoxy (n=3, 6,9,12,16,20)  water, free nonylphenol and/or polyethyleneglycols through repeated liquid/liquid extractions in appropriate solvent systems. In order to determine the influence of these secondary products on the processing yields, in this work experiments were performed with controlled addition (2%) of polyethyleneglycols (PEG 6 ) with an oligomerization degree (n = 6) ( Figure 15) and free nonylphenol (NF-OH) (4%), respectively ( Figure 16). The controlled sequential additivation of these secondary products in the exhaustive acid hydrolysis step of βnonylphenoxypropionitrile (NF-O-PN) affects overall the composition and processing yields by lowering the yields of β-nonylphenoxypropionic acid (NF-O-PC) at the expense of the esters NF-O-PE formed through the derivatization of the hydroxyl terminals in PEG and NF-OH.
If nonylphenoxypropionitrile is hydrolyzed with initial addition (cyanoethylation step) of polyethyleneglycols, the post-hydrolysis final mixture is even more complex due to the esters also formed by the exhaustive acid hydrolysis of nitrile functional groups in dicyanoethylated polyethyleneglycols and cyanoethylated nonylphenol, respectively.
Water was removed from the technical processes before processing by heating under effective stirring (without foaming) at 80-90°C under vacuum (10 -2 -10 -3 mm Hg). The content of free nonylphenol in the initial technical polyethoxylated product varies inversely with the oligomerization degree of ethylene oxide grafted on the hydroxyl functional group. From Figure 15 it is observed that together with the increase of the oligomerization degree in the homologous series n = 3 → 16, the proportion of NF(EO) n PN and NF(EO) n PC, β-nonylphenoxypolyethyleneoxy (n = 3-20) propionic acids, decreases continuously, while the proportion of β-nonylphenoxypolyethyleneoxy (n = 3-20) propionic acid esters, NF(EO) n PE, increase continuously in the same order. In the case of β-nonylphenoxypolyethyleneoxy (n = 3-20) propionamides [NF(EO) n PD], their concentration increases initially (60 minutes), after which reaches a maximum and decreases continuously until the disappearance from the processing medium, initially due to the partial acid hydrolysis of NF(EO) n PN to NF(EO) n PD, and later due to the partial acid hydrolysis of NF(EO) n PD to NF(EO) n PC. The relatively low amount [2-12% NF(EO) n PE] is due to the esterification under the specified conditions of NF(EO) n PC with NFOH present through the controlled additivation, and not due to the scission of the "ether bridge" under the pH and temperature conditions of the processing. In comparison with the processing attempts with polyethoxylated nonylphenols (n = 3-20) not purified from PEG and NFOH, the same processing yields are lower for NF(EO) n PN and NF(EO) n PD, as the acrylonitrile monomer is partially consumed in the derivatization of polyethyleneglycols (cyanoethylation) at the two hydroxyl terminals and the cyanoethylation of free nonylphenol, respectively. The final processing mixtures are more complex also in their colloidal behavior, together with the change of the hydrophilic/hydrophobic balance of the initial binary system.
In this work an increasing percental molar ratio of the acid catalyst (DBSH) was used (0.1/1-4/1) in relation to βnonylphenoxypolyethyleneoxy (n = 3-20) propionitrile to ensure in the end, after stoichiometric neutralization with inorganic or organic bases, respectively, the controlled proportion of the anionic surface-active component in the proposed binary colloidal system.
Depending on the working conditions and those of the processing of the reaction products, two classes of compounds were obtained: the free acids or their salts [NF(EO) n PC, (soaps)] with surface-active properties.
The evolution of the total hydrolysis yields was negatively affected by the heterogeneity of the processing environment (biphasic system), but favorably by the phenomena of micellar catalysis and/or in emulsion and of phase-transfer catalysis (PTC), respectively (Figures 17, 18). The idea of checking the influence of the phase-transfer catalysts on the exhaustive acid hydrolysis emerged after finding that in the previous cyanoethylation process, the yields increase simultaneously with the oligomerization degree of the polyoxyethylene chain in the homologous series n = 3, 6, 9, 12, 16, 20 ( Figure 19). This observation was explained by its active participation in the activation of the reaction intermediates with cationic structure I-V in Figure 20 by the "sandwich" and/or helical conformation of the polyoxyethylene chains [14], depending on the size of the oligomerization degree. The previously formulated hypothesis was confirmed by studying the evolution of the yields of the exhaustive acid hydrolysis of β-nonylphenoxy (n = 0) propionitrile [NF-O-PN] with and without the addition of PTC [1][2][3][4] . The presence of PTC in the hydrolysis medium increased the reaction yields by approx. 4% (Figures 17, 18).
In all cases, above 80°C the content of β-nonylphenoxy (NF) polyethyleneoxy (n = 3, 6,9,16,20) propionitrile drops sharply regardless of the acid catalyst used, and the continuous increase of the presence of propionic esters is observed. Increasing the processing time favors the total acid hydrolysis. Above 80°C (particularly in the version of hydrochloric acid catalysis), after ca. 60 minutes βnonylphenoxy (n = 0) propionitrile could not be found  in the reaction mixture, and after 90 minutes neither the intermediately formed propionamide.
In Figure 21 is presented in a schematized manner the probable coordination (sequestration) mode of the intermediates with cationic character (I-V) in Figure 20, in the "sandwich" model for the spatial conformation of PTC 2 and PTC 3 in order to be transferred through the interface separating the two phases (media) (organic and aqueous). The unitary operation is favored by the concentration potential difference between them, but also by the Figure 19 Scheme of the principle of coordination in non-polar solvents of alkali cations in the cavity of the polyoxyethylene chain with 8-9 oxygen atoms of β-nonylphenoxy-polyethyleneoxy-propionitriles. Simultaneously with the movement in the aqueous phase the recovery of the acid catalyst occurs, as well as its separation from the β-substituted propionic acid formed, the transfer through the separation interface and the preparation of the system for a new cycle of assisted exhaustive acid hydrolysis. The experimental attempts conducted with PTC 1 and PTC 4 , respectively, led to similar results, confirming that all coordination models, "cage", "sandwich" (Figure 21) and "tunnel" (Figure 22), favor the exhaustive acid hydrolysis.

Preparation of β-nonylphenoxy (NF) polyethyleneoxy (n = 3-20) propionitriles
In a thermostated processing vessel, fitted with mechanical stirring and condenser, under inert atmosphere 0.1 moles polyethoxylated nonylphenol, purified of water, polyethyleneglycols and/or free nonylphenol and 0.0025 moles basic catalyst CH 3 O -Na + are introduced at a convenient temperature (30-35°C), 0.0025 moles (0.38 g) finely divided anhydrous FeSO 4 are suspended and 5.83 g (0.11 moles) acrylonitrile are added cautiously under effective stirring, over 30-45 minutes, so that the temperature of the mixture does not exceed the prescribed value (if necessary the processing vessel is cooled in an ice-water bath). The mixture is maintained under similar conditions for 2 hours for perfecting the process, the basic catalyst is neutralized with ca. 4.8 mL solution CH 3 COOH 5% and the precipitated salts are filtered hot; the viscous residue, a fluid of slightly yellow color, is purified if necessary of acrylonitrile oligomers by elution at 40-60°C on a silica gel column. The main characteristics of the β-nonylphenoxy (NF) polyethyleneoxy propionitriles obtained are shown in Table 3. The cyanoethylation yields based on the introduced polyethoxylated nonylphenol are practically quantitative. Figure 22 Conformational structures of the phase-transfer catalysts (PTC 1-4 ) used in the exhaustive acid hydrolysis of nonylphenoxypropionitriles [26].  , as well as that of inorganic and/or organic dodecylbenzenesulfonates, respectively. The yields based on the nitriles introduced in hydrolysis are between 98-99%. The main physico-chemical characteristics of β-nonylphenoxy (NF) polyethyleneoxy (n = 3, 6,9,12,16,20) propionic acids are shown in Table 4. The amount (content) of water is evaluated with the relation: Where: m 1 amount of polyethoxylated nonylphenol (n = 3-20), technical product accessed (g) m 2 amount of polyethoxylated (n = 3-20) and free nonylphenol after drying to constant weight (g). The dried (hygroscopic) polyethoxylated product is kept further in the desiccator (P 2 O 5 ) for further determinations and/or processing.
Determination (separation) by liquid-liquid extraction of the content of polyethoxylated (n = 3-20) and free nonylphenol in dried technical products 1-2 g dried polyethoxylated (n = 3-20) and free nonylphenol, weighed with analytical precision in a previously tared 50-100 mL beaker, are dissolved in 5-10 mL ethyl acetate, neat, or with a minimal addition of saturated NaCl solution, then transferred quantitatively (by repeated washings with minimal amounts of solvent) into a 250-mL separation funnel. The mixture is shaken vigorously, repeatedly, alternating with stages of decompression of the liquid-liquid extraction system by rotating with 180°and cautiously opening the stopcock of the separation funnel. It is allowed to stand until complete separation of the organic phases from the combined aqueous ones (tendencies of stable emulsification at low oligomerization degrees). We recommend turning the separation funnel in both directions, horizontally on the ring. The reunited organic phases (ethyl acetate) are dried by filtration over anhydrous Na 2 SO 4 , then evaporated in a vacuum-connected installation (10 -2 -10 -3 mm Hg).
The product with appearance and fluidity dependent on the oligomerization degree, weighed with analytical precision (m 4 ) contains the mixture of polyethoxylated (n = 3-20) and free nonylphenol, and polyethylene glycol from the dried product accessed: Where: m 2 amount of dried polyethoxylated nonylphenol (n = 3-20), technical product accessed in the analysis (g) m 4 amount of free nonylphenol and/or polyethylene glycol evaluated after the evaporation of the combined ethyl acetate phases (g). The reunited aqueous phases (saturated NaCl solution) are liquid-liquid extracted repeatedly (2-3 times) with chloroform observing the same working protocol, the organic and inorganic (aqueous) phases, respectively, are completely separated and collected in tared flasks of adequate capacity.
The reunited chloroform phases are filtered (dried) over a layer of anhydrous Na 2 SO 4 and then evaporated in a previously tared flask in a vacuum-connected installation (10 -2 -10 -3 mm Hg). The product with appearance and fluidity dependent on the oligomerization degree, weighed with analytical precision (m 3 ) contains the free polyethyleneglycols (PEG n ) in the analyzed product: Where: m 2 amount of dried product accessed in the analysis (g) m 3 amount of product evaluated after the evaporation of the combined chloroform phases free of polyethyleneglycols (PEG n ) (g).
Determination (separation) by liquid-liquid extraction of the content of free nonylphenol in polyethoxylated nonylphenol (n = 3-20) chains 1-2 g analyzed mixture weighed with analytical precision in a previously tared 50-100 mL beaker, is dissolved in 5-10 mL 96% ethyl alcohol, then transferred quantitatively (by repeated washings with minimal amounts of solvent) into a 250-mL separation funnel. A similar volume of petroleum ether (b.p. = 30-60°C) is added, the mixture is shaken vigorously, repeatedly, alternating with stages of decompression of the liquidliquid extraction system by rotating with 180°and cautiously opening the stopcock of the separation funnel. It is allowed to stand for the complete separation of the organic phases (stable emulsification at low oligomerization degrees). For "breaking" the emulsion and complete separation of the phases the separation funnel is rotated horizontally in both directions on the ring.

Conclusions
Taking over critically from the literature issues related to nonionic soaps in the context of steadily increasing demands of assortment diversification, this work succeeded in presenting preparative and structural aspects related to the synthesis of alkaline and ethanolammonium β-nonylphenoxy (n = 0) propionates and alkaline and ethanolammonium β-nonylphenolpolyethyleneoxy (n = 3-20) propionates, respectively, accessing for the first time a scheme of classical reactions (cyanoethylation, exhaustive acid hydrolysis with DBSH and stoichiometric neutralization), which eliminated previously known and claimed disadvantages. The direct or indirect evolution of the processing yields was studied as a function of the structural parameters, proper process parameters (temperature, nature and concentration of catalyst, molar ratio of participants), process byproducts.
In the heterogeneous stages of the accessed operation block schemes special attention was given to the role of the interphase transfer catalyst in general, and of the polyoxyethylene chains (PEO) grafted as such and/or derivatized (phase-transfer catalysts PTC) in particular.
Starting from polyethoxylated nonylphenols, technical products contaminated with traces of water, free nonylphenol and/or polyethyleneglycols with various degrees of oligomerization, after specific purification by liquid/liquid and/or solid/liquid extractions in appropriate intervals of temperature, basic catalyst, duration, molar ratio of reactants, acrylic monomer polymerization inhibitor, etc., the influence of these operating parameters on the processing yields was quantified.
The reversibility of cyanoethylation upon prolonged contact of the reaction products with the basic catalyst was also confirmed.
Accessing dodecylbenzenesulphonic acid allowed on the one hand the provision of high yields of exhaustive acid hydrolysis, and on the other hand confirmed the role of acid catalyst in the directed structuring of binary nonionic-anionic colloidal systems for food sanitation.
From the study conducted it can be concluded that structurally the behavior of nonylphenols in the adopted reaction scheme can be divided into two distinct areas: for nonylphenol alone (n = 0) and for polyethoxylated nonylphenols (n = 3-20), respectively.
In the first case the low nucleophilicity of sodium nonylphenoxide due to (−I s ) and (+E s ) effects (p-π conjugation) affects cyanoethylation yields negatively. For this reason the presence of PTC 1 -PTC 4 -type phase-transfer catalysts favors the reaction by the coordination of the alkaline cation in the nucleophilic agent, the interphase transfer of the ionic species and catalyst (dodecylbenzenesulphonic acid). The role of micellar catalysis during the exhaustive acid hydrolysis phase cannot be excluded either.
In the second case the normal nucleophilicity specific to alkaline alkoxides (the electronic effects mentioned above being virtually non-existent) provides reaction yields increasing proportionally to the size of the polyoxyethylene chain in its own structure and with the coordination ability of the alkaline cation and/or other ionic species in the reaction medium, respectively. This work underlies and develops concepts, approaches synergistically, in an inter-and multidisciplinary manner the study of obtaining alkaline and ethanolammonium β-nonylphenolpolyethyleneoxy (n = [3][4][5][6][7][8][9][10][11][12][13][14][15][16][17][18][19][20] propionates, concerning the interdependence between structure and properties, promotes the idea of design, realization and access to new "highly qualified" nonionic soaps and open new topical thematic areas, with major impact on food sanitation. The synergistic pairing of individual colloidal competences into a single architecture allowed the monitored modification of the hydrophilic-hydrophobic balance (HLB), correlated with the appropriate changes in surface tension and critical micellar concentration of the new class of nonionic soaps.
Mathematical processing of the experimental data allowed on the one hand graphic evaluation of the development of the processes in a given range of variation of the work parameters, on the other hand the formulation of the closest mathematical relationship which would generalize the studied phenomenon. The high correlation coefficients confirm the "clustered" character of the experimental values recorded.